# Glossary

The words this site uses, in plain language. Each one links to the products that use it.

## Cabinet

One of three interchangeable names for the same physical product: cabinet, panel and tile all mean the self-contained dvLED unit an installer hangs, holding the LED modules, power supply and receiving card. A video wall is built from them.

## Calibration

Measuring every pixel and correcting it so the whole display shows one color and one brightness, with no patchwork between panels or batches.

## COB

Chip-on-board. The diodes sit directly on the circuit board under a hardened coating instead of in individual packages, which gives a seamless, impact-resistant surface and wide viewing angles.

## Common anode

An earlier power arrangement in which the red, green and blue chips share one positive connection and are driven from a single supply voltage. It was an early advance in dvLED, improving on the completely separate leads each subpixel had before it. Common cathode later improved on it in turn.

## Common cathode

A power arrangement in which the red, green and blue chips share one negative connection while each color gets its own supply voltage. It wastes less energy and runs cooler than the older common-anode design.

## Contrast ratio

The difference between the brightest white and the darkest black a display can show. LED pixels switch fully off, so blacks are black rather than gray.

## DVLED

Direct-view LED: a display whose picture is made by the LEDs themselves, with no backlight and no projector. Every Vanguard display is direct view.

## Epoxy coat

Another name for GOB. See GOB.

## Epoxy mask

Vanguard's name for a shallower epoxy treatment than GOB: a thinner layer that protects the LEDs while leaving more of their texture showing. The industry calls it HOB, sGOB or hGOB.

## Flip-chip

A way of mounting a diode face-down, with its contacts directly on the board and no bonding wires. Fewer parts to fail, better heat flow and a wider viewing angle. Flip-chip mounting was first used on integrated circuits, by IBM in the 1960s, long before it reached LEDs.

## Genlock

A timing signal that locks a display to cameras and broadcast equipment, so a screen appearing on camera stays in step with it.

## GOB

Glue-on-board, also called epoxy coat. A clear resin poured over a finished panel to seal the LEDs against knocks, dust and moisture. An option, not a pixel type. A shallower treatment, epoxy mask, protects the LEDs while leaving more of their texture.

## hGOB

Half GOB: an industry name for an epoxy mask. See Epoxy mask.

## HOB

Half on board: an industry name for an epoxy mask. See Epoxy mask.

## IMD

Integrated multi-pixel device. One package carries several pixels rather than one, which keeps the parts count down at fine pitches.

## Ingress protection

The IP rating: two digits saying how well a panel keeps out dust and water. IP65 front and rear suits outdoor weather; IP41 is an indoor rating.

## MIP

Micro-in-package. The newest pixel technology: very small diodes in a protective package, flip-chip mounted and common-cathode driven, which supports fine pitches without giving up durability.

## Nits

The unit of brightness, one candela per square meter. An indoor display needs a few hundred to a few thousand; a screen in direct sun needs several thousand.

## Panel

Another name for a cabinet or a tile: the same physical dvLED unit. The three terms are interchangeable. See Cabinet.

## Pixel density

How many pixels a square meter of display holds. It follows from the pitch: a finer pitch packs more pixels into the same area.

## Pixel pitch

The distance between the centers of two neighboring pixels, in millimeters. The smaller the pitch, the finer the image and the closer a viewer can stand before seeing individual pixels.

## Receiving card

The board inside a panel that takes the processed signal from the controller and tells each LED module what to show, keeping color, brightness and timing right across the wall.

## Refresh rate

How many times a second the display redraws its image, in hertz. A high refresh rate keeps motion smooth and stops the banding a camera would otherwise pick up.

## Scan rate

The proportion of a module's LED rows lit at any instant, written as a ratio such as 1/8. A lower ratio means each row is lit longer, which gives more brightness and a steadier picture.

## sGOB

Shrink GOB: an industry name for an epoxy mask. See Epoxy mask.

## SMD

Surface-mount device. Each pixel is a small package holding a red, a green and a blue diode under a protective lens, soldered to the board. The long-standing standard for LED displays.

## TAA

The Trade Agreements Act. A TAA-compliant product may be sold to US federal agencies and listed on GSA schedules. Vanguard's compliance was published in the Federal Register on 26 April 2018.

## Tile

Another name for a cabinet or a panel: the same physical dvLED unit. The three terms are interchangeable. See Cabinet.

## Viewing angle

How far to the side a viewer can stand and still see the picture at full brightness and true color, given in degrees horizontally and vertically.

Last updated 12 November 2026

---

Canonical: https://vanguardled.com/glossary/
